Decided to part out my Cervelo P3C to offset some of the costs for wedding plans. Located in NY, NY. Local pickup preferred.

http://www.autologicinc.com/...inceton/sell/p3c.jpg

2008 51cm Cervelo P3C frame and seatpost. $1100 + shipping and fees PENDING SALE
This P3C was formerly owned by pro jonnyo. Red, black and silver color scheme. The frame is excellent structurally but not cosmetically. Has two paint chips, one on the head tube, one on the seat tube. Some light scratches where the tire runs along the curved part of the frame and around the rear hub from wheel changes and the chain hanging in the area during transport. Finally, some glue residue remains near the bottom bracket from mounting a magnet for my Quarq powermeter. It really looks quite good unless you get real close and inspect, but I want to make the blemishes known to the buyer. I can include the 3T fork but the brake mounting bolt got stuck in there somehow (prompting the change to the edge fork)
http://www.autologicinc.com/...ceton/sell/p3c_6.jpg
http://www.autologicinc.com/...ceton/sell/p3c_7.jpg
http://www.autologicinc.com/...ceton/sell/p3c_8.jpg
http://www.autologicinc.com/...ceton/sell/p3c_9.jpg

Edge Aero 2.0 fork. $250 + shipping and fees PENDING SALE
Cut really short. Just long enough for most stems to fit on the P3C plus a small spacer. I have the Ventus on with a 20mm spacer below it. Could gain some more room if a shorter headset top cap is used.

3T Ventus LTD basebar. $300 + shipping and fees. PENDING SALE
Also purchased from Jonnyo. In good used condition. Elbow pads pads missing fabric covering. Carbon top cap has a small crack in it but holds fine. One small paint chip along the front edge. Comes with the spacers and hardware. Some of the spacer bolts should be replaced to prevent them stripping at the allen key hole.
http://www.autologicinc.com/...ceton/sell/p3c_1.jpg
http://www.autologicinc.com/...ceton/sell/p3c_2.jpg
http://www.autologicinc.com/...ceton/sell/p3c_3.jpg
http://www.autologicinc.com/...ceton/sell/p3c_4.jpg
http://www.autologicinc.com/...ceton/sell/p3c_5.jpg

Profile design t2+ cobra carbon extensions. $80 PENDING SALE
Uncut. Would prefer to sell these with the ventus bars or after those sell. Seen in the bar pictures above

Xlab 2.0 Carbon Clincher Disc. $500 + shipping
This is a light lenticular clincher disc. 700C. Shimano 10 speed hub. Great condition with stickers removed. Pictures below have a Surly fixer hub which can be included for extra.
http://www.autologicinc.com/...inceton/sell/XD1.jpg
http://www.autologicinc.com/...inceton/sell/XD2.jpg

Dura Ace 10 speed bar end shifters. $50 + shipping
Nice condition.
http://www.autologicinc.com/...ceton/sell/p3c_1.jpg

Vision Aero Brake levers $65 shipped
with bar end adapters. Great condition
http://www.autologicinc.com/...rinceton/sell/va.jpg

HED 3rd brake lever.
For Shimano Shifters. I have two. On one, the portion of the lever that goes into the mounting piece has some of the black anodize worn off. The other looks great. $50 shipped for the worn one and $65 shipped for the one in great condition.
More info here: http://www.hedcycling.com/...hird_brake_lever.asp
http://www.autologicinc.com/...nceton/sell/h3b1.jpg
http://www.autologicinc.com/...nceton/sell/h3b2.jpg
http://www.autologicinc.com/...nceton/sell/h3b3.jpg

Tacx bottle clamp. SOLD
Modified to fit on a p3c without the arm portion.
http://www.autologicinc.com/...ceton/sell/tacx1.jpg
http://www.autologicinc.com/...ceton/sell/tacx2.jpg