Official Fit Assistance for Profile Design Bars

Sorry for slow reply, it’s a bit more involved than the normal calc.

I do need to clarify where you’ve measured the Pad X to?
If it’s rear, the closest I can get is 498 with a stem to fit the HSF Aeria
If it’s centre then it’s less of a drama.

Sorry that’s an important piece of info I should have specified. 510 is to pad center.
Thanks.

Cool thread.

Can you give me 660mm pad stack and 515mm pad reach to back of pad w/ 15* of tilt for Aeria Ultimate bar and stem? What would that backwards calculate to frame stack and reach? I’m in between two frame sizes… QR PR5.

thanks,
Eric

As far as I can tell it takes ~20mm of spacers (incl hset cover) to match the height of the QR bento
But the 56 is nearly at max pad reach (11 out of 12 row options where 1 is most set back)
58.5 is a less extreme pad position (but gives the room to lengthen out)

The difference between pad row column and description is that description splits the high level view down to exact placement on the bracket
.
emp.jpg

As far as I can tell it takes ~20mm of spacers (incl hset cover) to match the height of the QR bento
But the 56 is nearly at max pad reach (11 out of 12 row options where 1 is most set back)
58.5 is a less extreme pad position (but gives the room to lengthen out)

The difference between pad row column and description is that description splits the high level view down to exact placement on the bracket

Thanks, I suspected as much. The client is in between sizes from both a fit and a bar choice perspective.

Eric

I’m trying to find the vertical height gain measurement of the 50 degree extensions, but at a loss. Do you know the measurement from centre to top? Thanks.

I keep a handy sheet of extension dimensions. That should help you find something.

Wow, thanks. Super helpful.

I was under the impression that Aeria Ultimate had pad and aero extension tilt capability, but I’m on the Profile Design site and that does not appear to be the case unless I’m missing it. There is plenty of lateral (left and right, fore and aft, and some toe-in), and a ton of vertical adjustment with many riser options, but I don’t see angled shims to tilt. Is there a way to add any pad and extension tilt? -c

Angled shims are a bodge to fix aerobars that lack tilt (with a couple of exceptions where they are part of a cohesive design approach)
https://www.slowtwitch.com/articles/images/4/159384-largest_rotation_640.jpg

You can see on the AU bracket that it tilts on the curved mount (where the numbers are)
.

Thanks for your quick reply, that’s exactly what I’m looking for! Mine shipped with a different bracket (image). I think I found the angle adjustable bracket on their site (link copied below). Does this look right? -c
https://profile-design.com/collections/aerobar-brackets/products/aeria-ultimate-race-bracket-kit

au small.jpg

Sorry, forgot to attach the image…

au small.jpg

You have an Aeria 1, not an Aeria 2 (which the UItimate is).
If you have an Aeria 1 you can’t use the Aeria 2 brackets, you would need to order an Evo bracket https://profile-design.com/...ucts/evo-bracket-kit
The Evo was designed specifically to add tilt to the older model bar - PD had sold many thousands of those so didn’t want to leave users without a solution to add tilt and better adjustment range

New products shown at Eurobike (continuing from the thread about WS)
Everything aside from the brackets is new in this image

43ASC (aero shaped carbon) extensions with Race+ armrests on a Wing Ultimate basebar

The principle behind the extension was to sweep the extension body across and up to where the riders arm is. The idea being to make one body from the perspective of the wind. CFD analysis was promising and led to the fin that tucks into the inside of the wrist.
Obviously there are length constraints, so a shorter option will follow a few months after this one.

Race+ armrest is a 40mm longer version of the Race, with a new 5-10-5mm tapered pad and grooved surface (same as Ergo+) for traction and moisture wicking

Wing Ultimate addresses the weight penalty of the Aeria Ultimate stem by integrating the stem.

asc.jpg
asc2.jpg

Wao, looks great.

Will the Aeria Ultimate bottle stil fit?

Will the Aeria Ultimate bottle stil fit?

Not really, need to do a new bottle
This bar is much slimmer at the front, so there are big gaps with the HSF Aeria bottle
.

Ok, as long as it is planned, this bar is an option for me :wink:

Just waiting for a good bottle solution as I’m not using the Aeria system until now.

GTN have just posted good coverage on youtube, skip to about 8mins in.

https://youtu.be/4OTeEDuVRCo

Do you have any idea how to get angle adjustment on a J5/Supersonic bracket with risers (I think 50mm). Rotating around basebar leads to other fit problems…

Also, how long will the ASC extensions be in the large version uncut?

Thanks!

I don’t suppose you know if an official release date has been put on the 43ASC extensions?

I don’t suppose you know if an official release date has been put on the 43ASC extensions?

One of the sales team told me he is expecting product to ship in late September. Availability to the public in early November

Edited with updated information