Sorry it took so long on the pictures.

That looks great. My exact setup with the TriRig AlphaX so thank you for posting. Not sure why Torhans specifically makes this note on the product page "CERVELO frames: Use regular AeroBento Storage System".

So that verbiage is being changed. What I recommend is that if you have a Cervelo with the 3T Aduro stem, the AeroBento will fit perfectly. You can use the AeroBentoX. They both work on frames that have top tube boss mounts. For BMC bikes, I don't quite understand why the boss mounts are so set back. It will work for that bike, or I think the Dark Speed works bento would be a good option for that bike as well.

The AeroBentoX has more volume and just easier to use with Di2 and cable integration.

---

Hans Bielat
TorHans LLC Co-Founder, Owner, Chief Innovation Officer
http://www.torhans.com

Just got my Bento X last week. My PRsix bosses are set back a little bit, but I just plan on drilling another hole in the bottom of the Bento X to push it as far forward as possible.

---

Proud Member of Chris McDonald's 2018 Big Sexy Race Team "That which doesn't kill me, will only make me stronger"
Blog-Twitter-Instagram-Race Reports - 2018 Races: IM Florida 70.3, IM Raleigh 70.3, IM 70.3 World Championships - South Africa, IM North Carolina 70.3

hHow does the Bento X fit with Gen1 Speed Concept top tube? I've got an Alpha X on it so it will mate well on the front end, but wondering on the width as the Bento X measure a couple mm wider than the Speed Concept (by my ruler at least)... Otherwise looks like a great solution and super clean. Thanks.

It fits pretty well on the Gen1 SC. It is ever so slightly wider at the front, maybe a couple of mm. It does not line up with the boss locations though unless you are OK with it being several inches behind the stem. I am planning on drilling an extra hole.

https://drive.google.com/...H8sUJklJhNVewG2hzu8G
https://drive.google.com/...oqyvGggNe2uEEmWthT5x
https://drive.google.com/...b1cudehrqU0WDAbG5KV0
https://drive.google.com/...7iIZ0YmoN1S5eR2CQpFU

Thanks for the pics. That’s super helpful. So I wasn’t crazy in measuring the SC top tube as a hair wider than the Bento X but it looks clean nonetheless. I’d probably just drill holes to move it forward in my set up. I did that with my DSW pack but this should match even better.

Any pictures of how you routed the rear brake cable?

No pictures of mine but I basically followed the instructions from HeyhoSilver on the P3 page (about halfway down, after pictures of his setup).

http://forum.slowtwitch.com/..._thread_P4524586-15/

Have you determined if the (god awful) blipbox fits?

Sorry guys. Meant to post an update. The blip box fits if you turn it on its side. It's too wide to lay in their flat.

---

Favorite Gear: Dimond | Cadex | Desoto Sport | Hoka One One

Do you pic with blip box/bento x set up; I would like to see how wires look coming out etc.

I will snap a pic or two.

---

Favorite Gear: Dimond | Cadex | Desoto Sport | Hoka One One

Would someone with a Bento X be able to provide the dimensions below? I assume the width measurement that Torhans lists of 1.8" (4.6 cm) is for what's labeled as "A" in the photo below. I'm considering ordering one but wanted to confirm how it will fit with my top tube. Thanks!!

Anybody?

Thanks!

A = 45mm
B = 35mm
C = 30mm
D = 120mm
E = 220mm

Hi,
Did you find a proper bento box? If yes, which one?
I'm thinking of buying the Bento X and drill 2 new holes in the frame close buy the stem for my BMC TM02. thanks!